Reptilia AUS 34mm Scope Mount 1.93in Bore Height

The Reptilia AUS Mount is a one-piece riflescope mount for 34mm tube scopes, holding the optic at a 1.93in bore height on any M1913 Picatinny rail.

One tube diameter, one bore height, one machined body. There is nothing here to shim, stack or align — that work was done on the mill.

Reptilia describes the AUS Mount as the culmination of a two-year development program driven by an end user group. It is machined from billet 7075-T6 aluminum, finished in MIL-STD Type III hardcoat anodizing, and clamps to the rail through an anti-snag spring-loaded nitrided steel clamp. This version weighs 6.0 oz (169 g) and takes a 34mm scope tube.

1.93in is the tallest AUS height, and it is there for a head-up shooting position — a chassis with a high adjustable comb, a shooter working under night vision, or anyone who would rather bring the scope to the eye than the eye to the scope. Reptilia does not publish an objective clearance figure at this height, so measure your own objective bell against your rail rather than assuming the extra height solves it. Made in the USA.

Key Features

• 34mm tube, fixed: Machined for one ring diameter, so the scope beds on metal rather than on shims
• 1.93in bore height: Chosen at the mill, not adjusted on the rifle
• One-piece body: Rings and base are the same part, so there is no base-to-ring joint to move
• 6.0 oz (169 g): Billet 7075-T6 aluminum in MIL-STD Type III hardcoat anodizing
• Spring-loaded steel clamp: Stays open while you place the mount, then closes flush and anti-snag

Compatibility & Fitment

Fits riflescopes with a 34mm main tube, on any M1913 Picatinny rail — the flat-top receiver of a bolt-action precision rifle, a rail-topped action, or a flat-top AR-pattern upper. Reptilia publishes no objective clearance figure for this height, so check your objective bell against your own rail before ordering. Tube diameter and bore height are both fixed on this listing and neither is adjustable, so measure your scope's main tube and decide your height before ordering. Reptilia makes the same 34mm mount at 1.54in and 1.70in bore heights, and the same 1.93in height for a 30mm tube.

Technical Specifications

US Shipping & Support

Shipped from D&R Sports Center in the USA with fast, tracked delivery. Questions on fit, mounting or which model suits your setup? Our team is glad to help before and after your purchase.

Frequently Asked Questions

Is the mm figure a height or a tube size?
On an AUS Mount it is the scope tube diameter. This one takes a 34mm tube. Reptilia quotes bore height separately, and on this version it is 1.93in. That is the opposite of their ROF and DOT red dot mounts, where the height is the headline figure, so it is worth reading the two numbers carefully before ordering.

Will my scope fit?
Only if its main tube measures 34mm. A one-piece mount is machined to one diameter and cannot be shimmed down or opened out. Check the tube specification from the scope maker rather than measuring with a ruler, because 30mm, 34mm and 35mm are close enough to confuse by eye. Reptilia publishes no maximum objective diameter for the 1.93in version.

Which bore height should I choose?
Bore height sets how high your eye has to sit to see through the scope. A lower mount suits a rifle with a conventional stock and a low comb; a taller one suits a raised comb, a chassis with an adjustable cheek piece, or a shooter who wants a head-up position. Reptilia offers this mount at more than one height and they are separate products, because a one-piece mount cannot be adjusted after it is made.

Does it hold zero if I take it off?
The clamp indexes into the rail slots, so return to zero is repeatable when the mount goes back into the same slots on the same rail. Note which slot you were in before removing it, and confirm the zero on paper afterward rather than assuming it — that is ordinary practice with any Picatinny mount, not a caveat about this one.